Desa CGCFTP Bedienungsanleitung PDF herunterladen (Seite 10)

10

107036

VENT-FREE PROPANE/LP GAS COMPACT FIREPLACE

CGCFTP

13"

16"

19"

21"

2

1

/2"

6"

8"

10"

Note:

All vertical

measurements

are from top of

fireplace

opening to

bottom of

mantel shelf. All

measurements

are in inches.

MANTEL CLEARANCES FOR

BUILT-IN INSTALLATION

If placing mantel above built-in fireplace,

you must meet minimum clearance between

mantel shelf and top of fireplace opening.

Figure 12 - Minimum Mantel Clearances

for Built-In Installation

Mantel Shelf

Side of

Firebox

INSTALLATION

Continued

Figure 13 - Attaching Brass Trim to Fireplace

OPTIONAL MANTEL

INSTALLATION

Note:

Refer to instructions provided with

the mantel for assembly instructions. Refer

to instructions below for system installa-

tion. Refer to instructions on page 4 for

firebox assembly. Blower accessory should

be installed if it is being used (see Installing

Blower Accessory GA3450T, pages 11

through 13).

1. Unscrew four brass screws that attach

top louver to fireplace. Remove louver

from fireplace and set aside.

2. Place fireplace on wood base.

3. Place mantel around fireplace/base

assembly.

4. Assemble brass trim kit. See Assem-

bling Brass Trim, page 11.

5. Firmly snap brass trim kit on shoulder

screws. Shoulder screws are located on

fireplace cabinet (see Figure 13).

6. Align brass trim kit for flush fit around

opening.

7. Use two 3" wood screws provided and

attach fireplace base to wooden base

(see Figure 13).

Figure 14 - Attaching Wood Base to Floor

1

3

/4" Screw

Wood Base

8. Remove brass trim kit and mantel. Be

careful not to damage wall or mantel.

9. Place wood base next to wall at instal-

lation location.

10.

Attach wood base to floor with two 1

3

/

4

"

black screws provided (see Figure 14).

If the floor is concrete use anchor

method (see Attaching Wood Base to

Solid Floor, page 14).

11. Install gas line. See Connecting To Gas

Supply, page 14.

12. Check for leaks. See Checking Gas

Connections, page 16.

13. Place mantel around fireplace. Be care-

ful not to damage wall or mantel.

14. Place brass trim kit on the shoulder

screws located on the side and top of

the fireplace. Firmly snap the brass trim

over the shoulder screws on fireplace

(see Figure 13).

15. Adjust assembly to remove any gaps.

Attach remaining two 3" wood screws

from hardware pack through openings

inside of fireplace sides into the mantel.

The openings are located at top behind

the area for the louvers (see Figure 13).

16. Reinstall top louvers.

Shoulder Screws

Assembled

Brass Trim

Hole for 3"

Wood Screw

for Attaching

Fireplace to

Wooden Base

Hole for 3"

Wood Screw

for Attaching

Fireplace to

Mantel

NOTICE: Surface temperatures of

adjacent walls and mantels be-

come hot during operation. Walls

and mantels above the firebox

may become hot to the touch. If

installed properly, these tempera-

tures meet the requirement of the

national product standard. Fol-

low all minimum clearances

shown in this manual.

NOTICE: If your installation does

not meet the minimum clearances

shown, you must do one of the

following:

• raise the mantel to an accept-

able height

• remove the mantel

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare