Desa Ga3750a Bedienungsanleitung PDF herunterladen (Seite 10)

108319-01B

For more information, visit www.desatech.com

NOTICE: Shut off gas supply and disconnect heater

from gas supply. Contact a qualified service person

to do this.

IMPORTANT

: For clarity, gas valve assembly and grate/burner

assembly are not shown in Figures 24 and 25. They will, however,

be in your fireplace when you are installing the blower. Also for

clarity the firebox is shown with dotted lines.

1. Open lower louver panel as shown in Figure 24.

2. Attach the power cord to the blower motor by firmly pushing

the two female terminals at the end of the power cord onto the

two spade terminals on the blower motor.

3. Attach green ground wire from power cord to blower housing

using screw provided (see Figure 24). Tighten screw securely.

4. Place the blower under the firebox and against the lower rear

wall of firebox outer wrapper with the exhaust port directed

upward. Align the holes in the top mounting tabs of blower

with holes in wall of wrapper (see Figure 24). Using the two

screws provided, mount blower and tighten screws securely.

5. Be sure all wire terminals on blower are attached securely.

Make sure the screw retaining the green wire is tight.

6. Remove screws securing the plate containing the ON/OFF

switch to the bottom of the firebox and set aside.

7. Place speed control against the back of this plate and push the

plastic control shaft through opening (see Figure 25).

8. While supporting speed control, secure control shaft with lock

nut by pushing and turning lock nut with pliers clockwise un-

til tight against the plate. Place control knob (provided) onto

shaft (see Figure 25).

9. Replace plate containing switches and tighten screws securely.

10. Plug in blower power cord.

a. If your fireplace system is installed as a freestanding unit

with an accessory mantel, determine whether the power cord

will exit the left side or the right side of the firebox. Install

one plastic bushing (provided) into the 1

/2" hole in the outer

casing through which the power cord will exit. Install the sec-

ond plastic bushing (provided) into the floor support bracket

if exiting through the right side (see Figure 26, page 11). Route

power cord through (both) plastic bushing(s) and plug the

power cord into a properly grounded 3-prong wall receptacle

near the firebox.

INSTALLING BLOWER

ACCESSORY IN DIRECT-VENT

FIREPLACE SERIES BHDV,

(E)BDV, DDV, HDV, CDV, CHDV,

DVF(E), OR DVFH

IMPORTANT:

Read all installation instructions be-

fore installing blower.

b.If your fireplace system installation is recessed and/or

pre-wired, a qualified installer must make all electrical con-

nections for the outlet kit included with the fireplace.

11. Check to make sure that the power cord is completely clear of the

blower wheel and that there are no other foreign objects in blower

wheel. Turn blower on and check for operation. Turn blower off

by rotating knob fully counterclockwise before continuing.

Figure 24 - Mounting Blower to Firebox

Lower Rear

Wall of

Firebox

Wrapper

Lower Louver

Panel

Screw

Exhaust Port

Blower Assembly

Green

Ground Wire

Screws

Figure 25 - Attaching Speed Control to Firebox

Speed Control

Control Shaft

Locknut

Control

Knob

Switch

Plate

CAUTION: Never touch the blower wheel while in

operation.

INSTALLING BLOWER ACCESSORY IN DIRECT-VENT FIREPLACE SERIES

BHDV, (E)BDV, DDV, HDV, CDV, CHDV, DVF(E), OR DVFH

1 2 ... 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Desa Ga3750a Bedienungsanleitung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Desa Ga3750a